中文字幕理论片,69视频免费在线观看,亚洲成人app,国产1级毛片,刘涛最大尺度戏视频,欧美亚洲美女视频,2021韩国美女仙女屋vip视频

打開APP
userphoto
未登錄

開通VIP,暢享免費電子書等14項超值服

開通VIP
關于串口控制投影機的操作方法的幾個步驟
關于串口控制投影機的操作方法的幾個步驟

 1、將中控接上電源,連好控制面板

2、將中控主機串口(RS232)接口與電腦主機COM口連接好

3、將中控系統隨機的光盤放入電腦中,打開“串口寫碼程序”軟件

4、寫碼程序設置處理:

A:選擇電腦的COM口,注意該端口不能被占用掉,否則無法與中控通訊

B:選擇輸入碼格式,16進制還是ASCII碼

C:選擇波特率

D:點擊“電源開”鍵,并清空輸入窗,按照投影機燈泡“電源開”的標準串口碼輸入到窗口中,并點擊“確認”鍵后再點擊“發送”鍵,此時應在控制面板上聽到“嘟”—“嘟”兩聲接收蜂鳴,表示該碼發送并成功接收到中控芯片中。

E:依次將“電源關”、“計算機”、“視頻”鍵的串口碼輸入到中控中。

F:將中控主機控制投影機端口選擇“串口控制”接口,并將控制接插頭插入,在投影機機身上“computer”控制口或稱“RS232”控制接口上找到正確的接線端,一般投影機控制腳被明確表示出來,如三洋投影機,NEC,等為8針圓腳(4腳接地,1腳接收等)。愛普生是標準九針口(2腳接受,5腳接地)  ..........

 
市場上現流行的RS232接口有兩種:一種是標準9針接口,另一種是圓孔8針接口。

 

 
串口寫入程序文件夾里文件的說明:

1、串口寫碼程序為單機的中控寫碼程序,此程序不可導入和導出串口碼
2、串口寫碼程序_通用為通用的寫碼程序。
  A:根據選擇可對單機的中控和網絡中控進行寫串口碼,程序中里有個機器類別選擇即為此功能,現此中控為單機的中控;
  B:在原來的基礎上增加了串口碼文件可導入和串口碼可導出到文件的功能。在沒有串口碼文件時,
   先將串口碼輸入到投影機代碼輸入窗中,接著按導出代碼,然后將其取一文件名保存好,依次將投影機
   的所有串口碼導出并保存,有了串口碼文件后,將程序左邊所有的設置設好,接著點導入代碼按鈕,
   選擇相應的串口代碼文件后,出現一對話窗“導入結束,按“發送”開始”,此時點“OK”,再點
   發送即可,發送串口碼時,會有聲音提示,到最近一聲響時串口代碼就發送好了。
3、COM測試為串口代碼的測試軟件
4、投影機串口碼為有關的一些投影機串口代碼,可供參考
5、關于串口控制投影機的操作方法的幾個步驟為串口代碼寫入的一些注意事項,請仔細閱讀

MIMITSUBI

(三菱)


S50U S200U

 
9600bps

 
DIN-8P

RD:1

TD:7

GND:4

 
開機:30H,30H,21H,0DH

關機:30H,30H,22H,0DH

VGA1:30H,30H,5FH,72H,31H,0DH

視頻:30H,30H,5FH,76H,31H,0DH

SHAPR C30

(夏普)


DB9:


RD:2


GND:5


TD:3


9600bps

 
開機:50H,4FH,57H,52H,20H,20H,20H,31H,0DH

關機:50H,4FH,57H,52H,20H,20H,20H,30H,0DH

VGA1:49H,52H,47H,42H,20H,20H,20H,31H,0DH

視頻:49H,56H,3BH,44H,20H,20H,20H,31H,0DH

 

普樂士(PLUS)

U2 850W

19200 bps

 開機: BEH,EFH,02H,06H,00H,79H,C0H,E0H,00H,00H,00H,00H,00H

 關機:BEH,EFH,02H,06H,00H,A8H,C1H,E1H,00H,00H,00H,00H,00H

 VGA1:BEH,EFH,02H,06H,00H,0DH,C4H,D4H,00H,00H,00H,00H,00H

 視頻:BEH,EFH,02H,06H,00H,DCH,C5H,D5H,00H,00H,00H,00H,00H

 

 明  基

(X550)


DIN-8P

RD:7

 TD:3

 GND:外殼

19200 bps

  

開機: BEH,EFH,02H,04H,00H,57H,48H,01H,00H,01H,00H

 關機:BEH,EFH,02H,04H,00H,A7H,48H,01H,00H,02H,00H

 VGA1:BEH,EFH,03H,06H,00H,40H,D2H,01H,00H,07H,00H,00H,00H

 視頻:BEH,EFH,03H,06H,00H,D0H,D3H,01H,00H,07H,00H,01H,00H

 S-視頻:BEH,EFH,03H,06H,00H,20H,D3H,01H,00H,07H,00H,02H,00H

品牌 型號 串口碼


飛利普DB9:RD:2TD:3GND:5 1241PXG20波特率:9600開機:POWR(3空格)1(回車)關機:POWR(3空格)0(回車)視頻:IVED(3空格)1(回車)VGA1:IRGB(3空格)1(回車)VGA2:IRGB(3空格)2(回車)

NECDIN-8PRD:1GND:4TD:7 440 波特率38400VT650波特率:19200開機:02H,00H,00H,00H,00H,02H關機:02H,01H,00H,00H,00H,03HRGB:02H,03H,00H,00H,02H,01H,01H,09H視頻:02H,03H,00H,00H,02H,01H,06H,0EHS-視頻:02H,03H,00H,00H,02H,01H,0BH,13H

EPSONDB9:RD:2GND:5TD:35600和7700的投影機的6腳要接高電平810/600/800/820波特率:9600開機:PWR(空格)ON(回車)關機:PWR(空格)OFF(回車)RGB1(ANALOG):SOURCE(空格)11(回車)RGB1(DIGITAL):SOURCE(空格)12(回車)RGB1(RGB-VIDEO):SOURCE(空格)13(回車)RGB2(ANALOG):SOURCE(空格)21(回車)RGB2(RGB-VIDEO):SOURCE(空格)22(回車)RGB2(YCBCR):SOURCE(空格)23(回車)RGB2(YPBPR):SOURCE(空格)24(回車)視1:SOURCE(空格)41(回車)S視:SOURCE(空格)42(回車)
 5600/7600/5300/7350/7250開機:1BH,07H,01H,00H,03H,01H,F(xiàn)4H關機:1BH,07H,01H,00H,03H,00H,F(xiàn)5HVGA1:1BH,07H,01H,01H,00H,10H,EFHVGA2:1BH,07H,01H,01H,00H,11H,E8HS-VIDEO:1BH,07H,01H,01H,00H,22H,D7HVIDEO:1BH,07H,01H,01H,00H,21H,D7H
 7700開機:0x1d,0x00,0x09,0x01,0x01,0x00,0x03,0x01,0xf1關機:0x1d,0x00,0x09,0x01,0x01,0x00,0x03,0x00,0xf2視頻:0x1d,0x00,0x09,0x01,0x01,0x01,0x00,0x21,0xd3S:   0x1d,0x00,0x09,0x01,0x01,0x01,0x00,0x22,0xd2VAG1:0x1d,0x00,0x09,0x01,0x01,0x01,0x00,0x10,0Xe4BNC_RGB:0x1d,0x00,0x09,0x01,0x01,0x01,0x00,0x30,0xc4BNC_YcrCb:0x1d,0x00,0x09,0x01,0x01,0x01,0x00,0x40,0xb4DVI:0x1d,0x00,0x09,0x01,0x01,0x01,0x00,0x50,0xa4
 8000波特率:9600 開機:PWR;1(回車)關機:PWR;0(回車)VGA1:SRC;0(回車)視頻:SRC;2(回車)

3M
8775/8675波特率:19200
開機:BEH,EFH,03H,06H,00H,2AH,D3H,01H,00H,00H,60H,00H,00H
關機:BEH,EFH,03H,06H,00H,BAH,D2H,01H,00H, 00H,60H,01H,00HRGB1:BEH,EFH,03H,06H,00H,F(xiàn)EH,D2H,01H,00H,00H,20H,00H,00H
RGB2:BEH,EFH,03H,06H,00H,3EH,D0H,01H,00H, 00H,20H,04H,00H
視頻:BEH,EFH,03H,06H,00H,6EH,D3H,01H,00H,00H,20H,01H,00H
S-VIDEO:BEH,EFH,03H,06H,00H,9EH,D3H,01H,00H,00H,20H,02H,00H
DVI:BEH,EFH,03H,06H,00H,0EH,D2H,01H,00H,00H,20H,03H,00H

 

 

松下
松下
開機:02H,PON,03H
關機:02H,POF,03H
視頻:02H,IIS,“:”,VID,03H
S視頻:02H,IIS,“:”,SVD,03H
RGB1:02H,IIS,“:”,RG1,03H
RGB2:02H,IIS,“:”,RG2,03H

 

 

東芝
DIN-8 PRD:1 TD:7 GND:4


開機:02H,PON,03H
關機:02H,POF,03H  (有確認信息)
關機:02H,PSD,03H  (沒有確認信息)
VGA1:02H,IN1,03HVGA2:02H,IN2,03H
視頻:02H,IN3,03HS-VIDEO:02H,IN4,03H
CAMERA:02H,IN6,03H


 

三洋
DIN-8 PRD:1 GND:4

開機:C00(回車)關機:C01(回車)
關機:C02(回車)有確認信息
SLOT1 SELECT: C05(回車)
SLOT2 SELECT: C06(回車)
SLOT3 SELECT: C07(回車)
SLOT4 SELECT: C08(回車)

 

 

ASK
ASK
DIN-8 PRD:6 TD:4  GND:8
C90/C100 波特率:9600
開機:BEH,EFH,80H,06H,00H,00H,00H,01H,00H,01H,00H,00H,00H關機:BEH,EFH,80H,06H,00H,00H,00H,01H,00H,00H,00H,00H,00H
VGA1:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 00H,00H
DVI1:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 01H,00H
S1:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 02H,00H
V1:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 03H,00H
VGA2:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 04H,00H
DVI2:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 05H,00H
S2:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 06H,00H
V2:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 07H,00H


 

串口碼有兩種形式,一種是ASCII碼,另一種是16進制碼。16進制碼的每個數據之間要用空格分開。ASCII碼原樣輸入有空格的要空格,和回車的要回車,如果是回車在碼尾的就不用回車直接將“碼尾加回車”選項選上。
     投影機串口的接口一般有3種形式,一是9針的標準接口,一個是8針的圓接口,另一個是15針的標準接口。9針的接口一般為:2腳為信號接收端(其中松下的投影機是3腳為信號接收端),5腳為地。8針的圓接口一般為:1腳為信號接收端,4腳為地,其中明基的是7腳為信號接收端,外殼為地。15針的接口為:13腳為信號接收端,10腳為地。

富士通:
波特率:19200,ASCII碼,碼尾加回車
開機:IP@G回車IPRM01回車IP@Q回車
關機:IP@G回車IPRM02回車IP@Q回車
RGB1:IP@G回車IPRM03回車IP@Q回車
VIDEO:IP@G回車IPRM05回車IP@Q回車

愛其:
波特率:19200,ASCII碼,碼尾加回車
開機:C00回車
關機:C01回車
視頻:C06回車
計算機:C05回車
上:C3C回車
下:C3D回車
左:C3B回車
右:C3A回車
大:C30回車
?。篊31回車

明基:
波特率:19200,十六進制
POWER:BE EF 02 06 00 13 CE AA 00 00 00 00 00
INPUT SELECT:BE EF 02 06 00 C4 C8 8D 00 00 00 00 00
ZOOM+:BE EF 02 06 00 AD CD B4 00 00 00 00 00
ZOOM-:BE EF 02 06 00 7C CC B5 00 00 00 00 00


東芝
DIN-8 PRD:1 TD:7 GND:4
開機:02H,PON,03H
關機:02H,POF,03H  (有確認信息)
關機:02H,PSD,03H  (沒有確認信息)
VGA1:02H,IN1,03HVGA2:02H,IN2,03H
視頻:02H,IN3,03HS-VIDEO:02H,IN4,03H
CAMERA:02H,IN6,03H

NEC
DIN-8P
RD:1
GND:4
TD:7
 440
波特率38400
VT650
波特率:19200
LT220+/240+/260+
波特率
38400或9600
MT860/1060/1065
波特率:38400
開機:02H  00H  00H  00H  00H  02H
關機:02H  01H  00H 00H 00H 03H
RGB:02H 03H 00H 00H 02H 01H 01H 09H
視頻:02H 03H 00H 00H 02H 01H 06H 0EH
S-視頻:02H 03H 00H 00H 02H 01H 0BH 13H

NEC LT220這型投影機開機要發兩次碼,一次待機一次開啟
EPSON
DB9:
RD:2
GND:5
TD:3


5600和7700的投影機的6腳要接高電平

波特率:9600

 810/600/800/820/73/53
波特率:9600
開機:PWR(空格)ON(回車)
關機:PWR(空格)OFF(回車)
RGB1(計算機1)(ANALOG):SOURCE(空格)11(回車)  
RGB1(DIGITAL):SOURCE(空格)12(回車)
RGB1(RGB-VIDEO):SOURCE(空格)13(回車)
RGB2(計算機2)(ANALOG):SOURCE(空格)21(回車)
RGB2(RGB-VIDEO):SOURCE(空格)22(回車)
RGB2(YCBCR): SOURCE(空格)23(回車)
RGB2(YPBPR): SOURCE(空格)24(回車)
視1:SOURCE(空格)41(回車)
S視:SOURCE(空格)42(回車)
 5600/7600/
5300/7350/
7250


 開機:1BH 07H 01H 00H 03H 01H F4H
關機:1BH 07H 01H 00H 03H 00H F5H
VGA1:1BH 07H 01H 01H 00H 10H EFH
VGA2:1BH 07H 01H 01H 00H 11H E8H
S-VIDEO:1BH 07H 01H 01H 00H 22H D7H
VIDEO:1BH 07H 01H 01H 00H 21H D7H
 7700 開機:1dH 00H 09H 01H 01H 00H 03H 01H f1H
關機:1dH 00H 09H 01H 01H 00H 03H 00H f2H
視頻:1dh 00H 09H 01H 01H 01H 00H 21H d3H
S視頻:1dh 00H  09H  01H 01H 01H 00H 22H d2H
VAG1: 1dH 00H 09H 01H 01H 01H 00H 10H e4H
BNC_RGB: 1dh 00H 09H 01H 01H 01H 00H 30H c4H
BNC_YcrCb:
1dH 00H 09H 01H 01H 01H 00H 40H b4H
DVI: 1dH 00H 09H 01H 01H 01H 00H 50H a4H
寶施馬 8000
波特率:
9600
開機:PWR;1(回車)
關機:PWR;0(回車)
VGA1:SRC;0(回車)
視頻:SRC;2(回車)

PROXIMA
DIN-8P
RD:6
TD:4
GND:8
波特率:
9600 5150/5155/
6150/6155/
6100
日立
DB15
公頭
RD:13
TD:14
GND:10 TECHNICAL
波特率:
19200
 
開機:BEH EFH 03H 06H 00H BAH D2H 01H 00H             00H 60H 01H 00H
關機:BEH EFH 03H 06H 00H 2AH D3H 01H 00H             00H 60H 00H 00H
RGB1:BEH EFH 03H 06H 00H FEH D2H 01H 00H             00H 20H 00H 00H
RGB2:BEH EFH 03H 06H 00H 3EH D0H 01H 00H             00H 20H 04H 00H
視頻:BEH EFH 03H 06H 00H 6EH D3H 01H 00H            00H 20H 01H 00H
S-VIDEO:BEH EFH 03H 06H 00H 9EH D3H 01H 00H 00H 20H 02H 00H
DVI:BEH EFH 03H 06H 00H 0EH D2H 01H 00H 00H 20H 03H 00H

3M
DB15
公頭
RD:13
TD:14
GND:10 8775/8675/8647
波特率:
19200
優派 1065/750
波特率:
19200

 

松下
DB9:
RD:3
TD:2
GND:5
9600bps
開機:02H 50H 4FH 4EH 03H
關機:02H 50H 4FH 46H 03H
視頻:02H 49H 49H 53H 3AH 56H 49H 44H 03H
S視頻:02H 49H 49H 53H 3AH 53H 56H 44H 03H
RGB1:02H 49H 49H 53H 3AH 52H 47H 31H 03H
RGB2:02H 49H 49H 53H 3AH 52H 47H 32H 03H

東芝
DIN-8P
RD:1
TD:7
GND:4 380型/410(昆明)
9600bps 開機:02H 50H 4FH 4EH 03H
關機:02H 50H 4FH 46H 03H  (有確認信息)
關機:02H 50H 53H 44H 03H  (沒有確認信息)
VGA1:02H 49H 4EH 31H 03H
VGA2:02H 49H 4EH 32H 03H
視頻:02H 49H 4EH 33H 03H
S-VIDEO:02H 49H 4EH 34H 03H
CAMERA:02H 49H 4EH 36H 03H

東芝
DIN-8P
RD:1
TD:7
GND:4 新的機型
9600bps 開機:02H 50H 4FH 4EH 03H
關機:02H 50H 4FH 46H 03H  (有確認信息)
關機:02H 50H 53H 44H 03H  (沒有確認信息)
VGA1:02H 49H 4EH 31H 03H
VGA2:02H 49H 4EH 32H 03H
視頻:02H 49H 4EH 35H 03H
S-VIDEO:02H 49H 4EH 36H 03H
CAMERA:02H 49H 4EH 37H 03H

三洋
SU35
DIN-8P
RD:1
GND:4 波特率:
19200 開機:C00(回車)
關機:C01(回車)
關機:C02(回車)有確認信息
RGB1:  C05(回車)
VIDEO: C06(回車)

三洋
SU20
DIN-8P
RD:1
GND:4 波特率:
19200 開機:C00(回車)
關機:C01(回車)
關機:C02(回車)有確認信息
RGB1: C05(回車)
VIDEO:C07(回車)
SLOT3 SELECT: C07(回車)
SLOT4 SELECT: C08(回車)

愛其
DIN-8P
RD:1
GND:4 XNB3W
X984
MB3W
波特率:
19200 開機:C00(回車)
關機:C01(回車)
關機:C02(回車)有確認信息
RGB1:  C05(回車)
VIDEO: C06(回車)


Sony 
PX32 38400bps
偶校驗
poweron: A5H 01H 00H 01H 00H 01H 03H 00H 01H 00H 01H 17H 00H 80H 08H 00H 06H 40H 54H 2EH 00H 00H 00H A1H 5AH
powerOFF: A5H 01H 00H 01H 00H 01H 03H 00H 01H 00H 01H 17H 00H 80H 08H 00H 06H 40H 54H 2FH 00H 00H 00H A0H 5AH
INPUTA(computer)  : A5H 01H 00H 01H 00H 01H 03H 00H 01H 00H 01H 17H 00H 80H 08H 00H 06H 40H 54H 2BH 00H 00H 00H A4H 5AH
VIDEO   : A5H 01H 00H 01H 00H 01H 03H 00H 01H 00H 01H 17H 00H 80H 08H 00H 06H 40H 54H 2AH 00H 00H 00H A5H 5AH

Sony

PX11
PX35 38400bps
偶校驗
開機:A9H 17H 2EH 00H 00H 00H 3FH 9AH
關機:A9H 17H 2FH 00H 00H 00H 3FH 9AH
VGA1:A9H 17H 2BH 00H 00H 00H 3FH 9AH
VGA2:A9H 17H 2CH 00H 00H 00H 3FH 9AH
視頻:A9H 17H 2AH 00H 00H 00H 3FH 9AH

MIMITSUBI
(三菱)
S50U S200U
 
9600bps
DIN-8P
RD:1
TD:7
GND:4

開機:30H 30H 21H 0DH
關機:30H 30H 22H 0DH
VGA1:30H 30H 5FH 72H 31H 0DH
視頻:30H 30H 5FH 76H 31H 0DH


SHAPR
DB9:
RD:2
GND:5
TD:3
C30
(夏普)
9600bps
開機:50, H 4FH 57H 52H 20H 20H 20H 31H 0DH
關機:50H 4FH 57H 52H 20H 20H 20H 30H 0DH
VGA1:49H 52H 47H 42H 20H 20H 20H 31H 0DH
視頻:49H 56H 3BH 44H 20H 20H 20H 31H 0DH
普樂士(PLUS)
U2 850W
 19200 bps
開機: BEH EFH 02H 06H 00H 79H C0H E0H 00H 00H 00H 00H 00H
關機:BEH EFH 02H 06H 00H A8H C1H E1H 00H 00H 00H 00H 00H
VGA1:
BEH EFH 02H 06H 00H 0DH C4H D4H 00H 00H 00H 00H 00H
視頻:
BEH EFH 02H 06H 00H DCH C5H D5H 00H 00H 00H 00H 00H

明  基
(X550)
DIN-8P
RD:7
TD:3
GND:外殼 19200 bps
開機: BEH EFH 02H 04H 00H 57H 48H 01H 00H 01H 00H
關機:BEH EFH 02H 04H 00H A7H 48H 01H 00H 02H 00H
VGA1:
BEH EFH 03H 06H 00H 40H D2H 01H 00H 07H 00H 00H 00H
視頻:BEH EFH 03H 06H 00H D0H D3H 01H 00H 07H 00H 01H 00H
S-視頻:
BEH EFH 03H 06H 00H 20H D3H 01H 00H 07H 00H 02H 00H

明  基
(DX655)
DIN-8P
RD:7
TD:3
GND:外殼
LG
RT-JT40
DB9: 19200 bps 開機:
BEH EFH 02H 06H 00H 13H CEH AAH 00H 00H 00H 00H 00H
關機:
BEH EFH 02H 06H 00H 13H CEH AAH 00H 00H 00H 00H 00H
VGA1:
BEH EFH 02H 06H 00H C4H C8H 8DH 00H 00H 00H 00H 00H
視頻:
BEH EFH 02H 06H 00H C4H C8H 8DH 00H 00H 00H 00H 00H
S-視頻:
BEH EFH 02H 06H 00H C4H C8H 8DH 00H 00H 00H 00H 00H
OPTOMA

奧圖碼
DIN-3P
RD:3
TD:1
GND:2
從左向右看 EP-756 
9600 bps
開機:OKOKOKOKOK(回車)
關機:*(空格)0(空格)IR(空格)002(回車)
RGB1:  *(空格)0(空格)IR(空格)015(回車)
VIDEO: *(空格)0(空格)IR(空格)019(回車)


ASK
ASK
DIN-8 PRD:6 TD:4  GND:8
C90/C100 波特率:9600
開機:BEH,EFH,80H,06H,00H,00H,00H,01H,00H,01H,00H,00H,00H關機:BEH,EFH,80H,06H,00H,00H,00H,01H,00H,00H,00H,00H,00H
VGA1:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 00H,00H
DVI1:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 01H,00H
S1:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 02H,00H
V1:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 03H,00H
VGA2:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 04H,00H
DVI2:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 05H,00H
S2:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 06H,00H
V2:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 07H,00H



本站僅提供存儲服務,所有內容均由用戶發布,如發現有害或侵權內容,請點擊舉報。
打開APP,閱讀全文并永久保存 查看更多類似文章
猜你喜歡
類似文章
HC05藍牙模塊的使用
淺談串口通信(232,485,422)以及常見問題,心得體會等
PLC作主站,51單片機作從站,用ModBus協議進行通訊
用Android控制Arduino小車
串口通信及其常見問題
史上最全的機頂盒系統備份,系統升級操作方法詳細解說。
更多類似文章 >>
生活服務
熱點新聞
分享 收藏 導長圖 關注 下載文章
綁定賬號成功
后續可登錄賬號暢享VIP特權!
如果VIP功能使用有故障,
可點擊這里聯系客服!

聯系客服